Gas Monitor
Total Analytical Solution 
D-2-4, Setia Walk, Pusat Bandar Puchong,
47160 Puchong, Selangor, Malaysia
 
Tel: + 6012-921 3877; 603-5879 7121
Fax: +018 635 1593
Email: ancor.my@gmail.com
            sales@gasmonitors.com.my
   Home      Drager- Drager Polytron 5700
 

Dräger Polytron 5700

 
Quick, reliable and cost-effective detection of combustible gases and vapors in ambient air: the microprocessor-based transmitter is the result of more than 40 years of experience in measurement technology and contains a new, innovative IR sensor with drift-free optics. These optics are extremely resistant against deposits and insects in the beam.
 
 

Proven – and still getting better: Dräger measurement technology

Dräger has been developing and manufacturing sensors and gas detectors for industrial use for more than 40 years. And with each new device generation, we drive our measurement technology a bit further. With the Polytron 5700, you will definitely benefit from this experience and power of innovation. Its sensors are based on an open, double-compensated optical infrared system. This innovative design offers the following advantages:
  • short response times
  • low sensitivity to dust or dirt deposits on the optical surfaces and to insects in the measuring cuvette
  • longer maintenance intervals
  • drift-free output signal
  • high signal stability thanks to an extremely light-efficient optics with a 4-beam signal-stabilizing system
 
 

Optional: three relays for controlling external equipment

Upon request, the Dräger Polytron 5700 can be supplied with three integrated relays. This enables you to use it as an independent gas detection system with two arbitrarily adjustable concentration alarms and one fault alarm. Audio alarms, signal lights, or similar devices can, thus,
be controlled locally – without an additional cable between the transmitter and a central controller. The sensor signal can be evaluated using the 4 to 20 mA signal.
 
 

Quick and easy wiring

The electronics and the bezel form a single unit. Simply pull them out of the housing. Then insert the three-wire cable into the terminals – either through the Ex-e cable gland or through the seal on the conduit. Finally plug the terminal block into the PCB. 
 
 

Library containing up to 100 gases (types 334 and 340):

Each of the gases listed there can, for example, be cross-calibrated with vapors and preset gases, such as methane or propane. All calculations and linearizations are performed automatically. 
 
 

Optional: two mounting sets for easy flange-mounting

The housing has four mounting holes. Two different mounting sets are available for installing the Polytron 5700: a duct-mount and a pipe mount set. This means that the transmitter can be easily installed anywhere – e.g., on a smooth wall, a pipe or an exhaust duct. 
 
 

Easy and cost-effective: single-operator calibration

The transmitter settings can be changed and maintenance carried out without opening the housing. Declassification of the hazardous, classified area is not necessary. Use the magnetic wand to quickly and easily select menu items and functions. An additional hand held terminal is not required. 
 
 

Further advantages:

Available as flameproof or increased safety version
  • Aluminum or 316 L stainless steel housing for the most extreme industrial conditions
  • Extremely user-friendly software thanks to a minimum number of menu items
  • Backlit display: easy to read, even in the dark and without a flashlight
  • Traffic light status indicator (green = no danger, yellow = error, flashing red = gas alarm)
  • Beam block warning signal if the optics are heavily contaminated
  • Measuring ranges in the ppm, %LEL and Vol.% range
 
 
 
 
 
 
D-2-4, Setia Walk, Pusat Bandar Puchong,
47160 Puchong, Selangor, Malaysia

Tel: + 6012-921 3877; 603-5879 7121
Fax: +018 635 1593
Email: ancor.my@gmail.com 
           sales@gasmonitors.com.my