Gas Monitor
Total Analytical Solution 
D-2-4, Setia Walk, Pusat Bandar Puchong,
47160 Puchong, Selangor, Malaysia
 
Tel: + 6012-921 3877; 603-5879 7121
Fax: +018 635 1593
Email: ancor.my@gmail.com
            sales@gasmonitors.com.my
   Home      Status Scientific-FGD10 C5H12
 
 
 

Flameproof Gas Detectors FGD10 Series

Pentane Gas Detector

(using infrared sensor technology)

 

Features

  • Standard range, 0-2% Volume Pentane (C5H12).
  • NEW! - Now also available in Stainless Steel Grade 316 (as an alternative to aluminium).
  • Temperature compensated infrared sensor.
  • Plug-in, separately certified Ex d sensor.
  • Versions available with or without a display window.
  • Window version menu operates via a magnetic pen eliminating the need to open the flameproof enclosure.
  • Protective weather guard can be optionally fitted.
  • Can be used in conjunction with new LC Series single and multi channel control units in addition to the standard MCU range.
  • Output - 4 to 20 mA dc (3-wire).
  • 8 to 24 volt dc operation.
  • Display version is fitted with 3 control relays.
  • Various cable gland thread sizes available.

 

Type FGD10A - Display Version

Infrared Methane Gas Detector Type FGD10A
This version has a clear window behind which is fitted a 4 digit LCD display. Four magnetically operated switches behind the window allow the user to configure various operating parameters without opening the flameproof cover. The magnetic switches are operated from outside the window by means of a special magnetic pen.
Three control relays are fitted to provide Alarm Level 1, Alarm Level 2 and Fault outputs via individual changeover contacts. In addition to the 4 to 20 mA analogue, an RS 232 communications output is also provided.
 
 
 
 
 
 
 
 

Type FGD10B - Non-Display Version

Infrared Methane Gas Detector Type FGD10B

The non-display version provides a cost effective monitoring solution in situations where a local display of the gas level is not required. The unit provides a 4 to 20 mA output.

Calibration of the FGD10B can be carried out simply by using ZERO and SPAN buttons inside the instrument provided that the concentration of the calibration gas is the same as that used for factory calibration of the detector (refer to the instrument calibration certificate for details).

Alternatively, the purpose designed plug-in hand held configuration unit shown below may be used together with any appropriate test gas concentration.
 
 
 
 

FGD10B Calibration Unit

Configuration UnitCalibration of the unit requires the removal of the front cover of the flameproof enclosure and therefore must only be carried out under either of the following conditions:-
  1. In a safe area where there is no risk of the presence of an explosive gas.
  2. Within the hazardous area by authorised personnel under controlled conditions after it has been established that no flammable gases are present in the area. Note that a management or health and safety department permit may be required for this to be carried out.

To carry out a calibration, the operator must open the front cover of the unit, plug in the calibration unit and then present zero and span gases to the sensor during the course of the calibration procedure.

 
 

FGD10 Pentane Gas Detectors - Order Codes

Stock No. Description
SS711-5 FGD10A Pentane Gas Detector with Display (4-20mA, Relays & RS232 Outputs) - 0-2% Volume Pentane (C5H12)
SS731-5 FGD10B Pentane Gas Detector (No Display) (4-20mA Output) - 0-2% Volume Pentane (C5H12)
SS746 FGD10 Series Flow-Through Sampling Adaptor
SS747 FGD10 Series Calibration Adaptor c/w 1 Metre Tubing
SS748 FGD10B Configuration Unit with USB Cable
SS749 FGD10 Series Protective Weather Guard
SS840 Magnetic Pen for FGD10A Series

( -5 shown in above codes denotes the calibration gas type, i.e. Pentane)

 
 
 
 
 
 
D-2-4, Setia Walk, Pusat Bandar Puchong,
47160 Puchong, Selangor, Malaysia

Tel: + 6012-921 3877; 603-5879 7121
Fax: +018 635 1593
Email: ancor.my@gmail.com 
           sales@gasmonitors.com.my