- High quality glass tube
- Distinct layer of colour change
- Chemical formula of the substance to be measured
- Detector Tube Listing
|
Gas Sampling Pump GV-100S
- On-site measurements can be performed easily by anybody, anytime and anywhere, in a short time
- Easy-to-check direct reading possible due to the calibrated scale directly printed on the tube
- An extensive measuring range can be obtained by adjusting the sampling volume
- In order to assure high precision, each production lot
is tested and calibrated independently, Each detector tube has its own
quality control number printed on the tube
- Long shelf-life with excellent long-term stability
|
Gas Sampling Pump with Stroke Counter GV-110S
- The automatic sampling counter tells you how many pump strokes you
already completed even though GASTEC tubes normally do not require so
many pump strokes.
|
Gas Sampling Pump Kit GV-100S
- The pump accessories (3 rubber inlets and lubricant) as well as the instruction sheet are provided in a convenient shoulder bag.
|
Gas sampling pump kit with pump stroke counter GV-110S
- The automatic sampling counter tells you how many pump strokes you
already completed even though GASTEC tubes normally do not require so
many pump strokes.
- The pump accessories (3 rubber inlets and lubricant) as well as the instruction sheet are provided in a convenient shoulder bag.
|
Gas sampling pump kit GV-100LS
- The pump accessories (3 rubber inlets and lubricant) as well as the instruction sheet are provided in a convenient shoulder bag.
|
Smoke tester kit 500
- Break off both ends of the smoke tube and attach a rubber squeeze bulb
to one end of the tube.
- When the bulb is squeezed, a chemical reaction
produces white smoke.
- This smoke makes the air flow (in ventilation
systems/ducts, etc.)
- A single tube can be repeatedly used for
about 50 tests
|
Compressed Breathing Air Measurement Kit CG-1
- Gastec CG-1 system can simply, quickly, and simultaneously measure 4 kinds of harmful contaminants (CO, CO2, Water vapour, and Oil mist)
contained in compressed breathing air (cylinder or compressor).
-
Accurate simultaneous measurement of 4 impurities (CO, CO2, Water vapour, and Oil mist) in compressed breathing air achieved by simply connecting the device to a cylinder or compressor |
Toxic gas detection kit TG-I
- The primary step towards being able to prevent
hazardous gas generation at the workplace, as part of occupational
hygiene and pollution control, is to acquire accurate data regarding the
emitted gas types and their concentration levels.
- Our hazardous gas
detection kit consists of 12 detector tubes.
- There is no need to possess special technology, knowledge or skills.
- Operation is simple.
|
Flue gas measuring kit SG-1/SG-2
- The
Environmental Agency of Japan recommends this kit as a means of exhaust
gas detection.
- This kit is in use primarily at such smog generating
sources as turbines and diesel engines.
- Measurements SO2,NO2, and O2 in smoke and soot
- Measurement is completed in less than 60 seconds, enabling the measured results to be known on the spot.
|
Waste water test kit WPT-132/WPT-133/WPT-135
- Enables concentrations of organic chlorinated solvents
- Tetrachloroethylene, trichloroethylene present in wastewater to be
easily measured.
|
Waste water test kit WP-132/WP-133/WP-135
- Enables concentrations of organic chlorinated solvents
- Tetrachloroethylene, trichloroethylene present in wastewater to be
easily measured.
|
HYDROTEC-S330
- This kit enables quick measurement (approx. 10 min.) of sulphide in
bodies of water or in waste water without any special equipment and
skills.
- Take a sample with the gas generator tube, add sulphuric acid
and simply measure the amount of hydrogen sulphide generated using the
detector tube.
|
Arsenic Detection Kit 331
- This kit measures arsenic content in soil or in water. It takes about 15
minutes for the standard concentration of 0.01 to 0.5 mg/L in water.
The kit requires no battery or power supply.
|
Mercury Detection Kit 332
- This kit measures mercury content in soil or water.
- It takes about 10
minutes for common concentrations between 0.005 and 0.04 mg/L in water.
- The kit requires no battery or power supply.
|
Pyrotec pyrolyzer 840
- GASTEC developed the Pyrotec Pyrolyzer system to enable precise and easy
detection of fluorochlorocarbon gases.
- It converts fluorochlorocarbon
gases or halogenated hydrocarbons (using a process known as thermal
cracking) into an easily detectable/measurable gas.
|
Pyrotec pyrolyzer 860
- GASTEC developed the Pyrotec Pyrolyzer system to enable precise and easy
detection of Sulphuryl Fluoride.
- It converts Sulphuryl Fluoride (using
process known as thermal craking) into an easily measurable gas.
|
Fumigation Probe 380
- GASTEC fumigation probe is connected to gas detector tube and inserted
through rubber seal of the closed container to measure residue
fumigants.
- Currently app;icable tubes are limited.
|
Tube tip holder 722
- The Tube tip holder doubles as a detector tube tip breaker and a storage
receptacle for up to 260 broken tips, thereby preventing glass
fragments from scattering.
|
Rubber caps DTP-1-20/DTP-2-20
- Reusable rubber caps can be attached to the broken edges of the detector
tubes as an extra precautionary safety measure.
- Blue caps can be used
with the largest size detector tubes (outer diametre of 7mm) and pink
ones with all other tubes.
- One (1) package contains 20 caps.
- No.DTP-1-20(blue)
large-diametre tubes for tube nos.1HT, 1HH, 2HT, 2HH, 4HT, 31B (blue)
- No.DTP-2-20(pink)
for all type of gas detector tubes except the above
|
Extension hoses 351A-5/351A-10/351A-30
- Extension hoses are available to be attached to the inlet of the gas
sampling pump (Model GV-100) and used for remote downward measurement in
confined spaces, such as manholes, tanks, etc.
* For twin tube operation, order the Extension hose guard rubber
(No.358) .
- When the extension hose tip needs to be replaced, order the
Replacement extension hose guard rubber (No.359) .
- 351A-5 (for 5m long), 351A-10 (for 10m long), 351A-30 (for 30m long)
|
Hot probe/Hot probe holder 340/345A
- The hot probe is a cooling device for measuring hot gases (60 to 600ºC /
140 to 1112 ºF) such as exhaust from ehicles and incinerators by
cooling them down to normal temperatures.
- The stability of the device is
enhanced when it is secured with the hot probe holder (No.345A)
- Hot probe holder (Model 345A) can not be used with Twin-tubes and Oxygen tube No. 31B.
|
Extension pole 350BP-2
- Made of lightweight fiberglass and weighing only 590g, the extension
sampling pole has a compact body (62.5 cm) for easy portability and can
be extended to a maximum length of 2.8m.
|
Twin Tube Holder GV500
- The twin tube holder protects twin tubes from drop and damage or prevents injury to the user during a measurement.
|
One hand operation adapter GV-700
- GV-700 can maintain a vacuum of 50mL or 100mL in the pump body.
- This
allows the user to attach the appropriate tube to pump ,and then in
situations where it is necessary , to take the sample using one hand.
- In
the body of the Adapter there is a small rod which can be moved in or
out quite easily with one finger.
|
- Contaminant distribution can be easily and accurately determined.
-
A hole is drilled in the ground with the boring rod, and the
contaminants present in the gas in the hole are measured; by taking
measurements at multiple points on a site the exact distribution of
contaminants can be assessed.
|
Extension pole for sub-surface sampling 360
- Contaminant distribution can be easily and accurately determined.
- A hole is drilled in the ground with the boring rod, and the
contaminants present in the gas in the hole are measured; by taking
measurements at multiple points on a site the exact distribution of
contaminants can be assessed.
|
|
Dositube holder 710
- The passive dositube can then be positioned in the worker's breathing
zone where it can be attached with a holder and collar clip (separately
available : Art.No.710) and the amount of individual exposure can be
measured.
|
|